BU52002GUL,BU52003GUL,BU52012NVX,BU52012HFV,BU52013HFV
Technical Note
15/19
www.rohm.com
2010.08 - Rev.C
?2010 ROHM Co., Ltd. All rights reserved.
螴ntermittent Operation at Power ON
The unipolar detection Hall IC adopts an intermittent operation method in detecting the magnetic field during startup, as
shown in Fig.44. It outputs to the appropriate terminal based on the detection result and maintains the output condition
during the standby period. The time from power ON until the end of the initial startup period is an indefinite interval, but it
cannot exceed the maximum period, 100ms. To accommodate the system design, the Hall IC output read should be
programmed within 100ms of power ON, but after the time allowed for the period ambient temperature and supply voltage.
螹agnet Selection
Of the two representative varieties of permanent magnet, neodymium generally offers greater magnetic power per volume
than ferrite, thereby enabling the highest degree of miniaturization, thus, neodymium is best suited for small equipment
applications. Fig.45 shows the relation between the size (volume) of a neodymium magnet and magnetic flux density. The
graph plots the correlation between the distance (L) from three versions of a 4mm X 4mm cross-section neodymium magnet
(1mm, 2mm, and 3mm thick) and magnetic flux density. Fig.46 shows Hall IC detection distance a good guide for
determining the proper size and detection distance of the magnet. Based on the BU52012HFV, BU52013HFV operating
point max 5.0 mT, the minimum detection distance for the 1mm, 2mm and 3mm magnets would be 7.6mm, 9.22mm, and
10.4mm, respectively. To increase the magnets detection distance, either increase its thickness or sectional area.
Power ON
VDD
Startup time
Standby time
Standby time
Startup time
(Intermittentaction)
Indefinite
interval
OUT
(No magnetic
field present)
Indefinite
interval
OUT
(Magnetic
field present)
Low
High
Supply current
Fig.44
X=Y=4mm
t=1mm,2mm,3mm
X
t
Y
&Flux density measuring point
L: Variable
t
Fig.46 Magnet Dimensions and Flux Density Measuring Point
Magnet size
Magnet
Magnet material: NEOMAX-44H (material)
Maker: NEOMAX CO.,LTD.
0
1
2
3
4
5
6
7
8
9
10
0
2
4
6
8
10
12
14
16
18
20
Distance between magnet and Hall IC [mm]
Fig.45
7.6mm
t=3mm
t=1mm
t=2mm
9.2mm
10.4mm
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
BU52014HFV-TR
IC HALL EFFECT SW BIPO HVSOF5
BU52040HFV-TR
IC HALL EFFECT BIPO LATCH HVSOF5
D6B-2P
SENSR TILT 35-65DEG 1MA SMD GUL
D7E-3
SENSOR TILT 50-80DEG 0.1A GRY
DSBA1H
SENSOR TILT SW 30-60DEG 20MA TH
EE-SA103
SENSOR OPTO SLOT 3MM TRANS THRU
EE-SA107-P2
OPTO SENSOR 3.6MM TRANS
EE-SH3-DS
SENS OPTO SLOT 3.4MM TRANS SOLDR
相关代理商/技术参数
BU52004GUL
制造商:ROHM 制造商全称:Rohm 功能描述:Hall effect Switch
BU52004GUL_10
制造商:ROHM 制造商全称:Rohm 功能描述:Omnipolar Detection Hall ICs (Polarity detection for both S and N features dual outputs)
BU52004GUL-E2
功能描述:板机接口霍耳效应/磁性传感器 Magnetic Sensor 2.4-3.3V; 50mS RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
BU-5200-A-4-0
功能描述:测试引线 Black BNC Female Bre RoHS:否 制造商:Pomona Electronics 设备类型:Patch Cords 连接器类型:Banana plug (stackable) on both ends 长度:60 in 颜色:Black
BU52011HFV
制造商:ROHM Semiconductor 功能描述:Hole IC,Bop=+/-3.0mT,CMOSout,HVSOF5
BU52011HFV-STR
制造商:ROHM Semiconductor 功能描述:IC HALL BU52011HFV-STR
BU52011HFV-TR
功能描述:工业霍耳效应/磁性传感器 ULTRA SMALL DETECT SENSOR; 1.65-3.3V RoHS:否 制造商:Honeywell 操作类型: 操作高斯: 工作电源电压: 电流额定值: 封装 / 箱体: 输出下降时间: 工作点最小值/最大值: 安装风格: 最大工作温度: 最小工作温度: 最大输出电流: 封装:
BU52012HFV
制造商:ROHM 制造商全称:Rohm 功能描述:Unipolar Detection Hall ICs